 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| user?s manual target devices pd789407a subseries pd789417a subseries IE-789418-NS-EM1 emulation board 1991 ? document no. u14364ej3v0um00 (3rd edition) date published october 2002 n cp(k) printed in japan 1999
user?s manual u14364ej3v0um 2 [memo] user?s manual u14364ej3v0um 3 windows is either a registered trademark or a trademark of microsoft corporation in the united states and/or other countries. pc/at is a trademark of international business machines corporation. m8e 00. 4 the information in this document is current as of august, 2002. the information is subject to change without notice. for actual design-in, refer to the latest publications of nec's data sheets or data books, etc., for the most up-to-date specifications of nec semiconductor products. not all products and/or types are available in every country. please check with an nec sales representative for availability and additional information. no part of this document may be copied or reproduced in any form or by any means without prior written consent of nec. nec assumes no responsibility for any errors that may appear in this document. nec does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of nec semiconductor products listed in this document or any other liability arising from the use of such products. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec or others. descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. nec assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. while nec endeavours to enhance the quality, reliability and safety of nec semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. to minimize risks of damage to property or injury (including death) to persons arising from defects in nec semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. nec semiconductor products are classified into the following three quality grades: "standard", "special" and "specific". the "specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. the recommended applications of a semiconductor product depend on its quality grade, as indicated below. customers must check the quality grade of each semiconductor product before using it in a particular application. "standard": computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "special": transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "specific": aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. the quality grade of nec semiconductor products is "standard" unless otherwise expressly specified in nec's data sheets or data books, etc. if customers wish to use nec semiconductor products in applications not intended by nec, they must contact an nec sales representative in advance to determine nec's willingness to support a given application. (note) (1) "nec" as used in this statement means nec corporation and also includes its majority-owned subsidiaries. (2) "nec semiconductor products" means any semiconductor product developed or manufactured by or for nec (as defined above). ? ? ? ? ? ? user ? s manual u14364ej3v0um 4 regional information some information contained in this document may vary from country to country. before using any nec product in your application, piease contact the nec office in your country to obtain a list of authorized representatives and distributors. they will verify: ? device availability ? ordering information ? product release schedule ? availability of related technical literature ? development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, ac supply voltages, and so forth) ? network requirements in addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. nec electronics inc. (u.s.) santa clara, california tel: 408-588-6000 800-366-9782 fax: 408-588-6130 800-729-9288 nec electronics hong kong ltd. hong kong tel: 2886-9318 fax: 2886-9022/9044 nec electronics hong kong ltd. seoul branch seoul, korea tel: 02-528-0303 fax: 02-528-4411 nec electronics shanghai, ltd. shanghai, p.r. china tel: 021-6841-1138 fax: 021-6841-1137 nec electronics taiwan ltd. taipei, taiwan tel: 02-2719-2377 fax: 02-2719-5951 nec electronics singapore pte. ltd. novena square, singapore tel: 253-8311 fax: 250-3583 nec do brasil s.a. electron devices division guarulhos-sp, brasil tel: 11-6462-6810 fax: 11-6462-6829 j02.4 nec electronics (europe) gmbh duesseldorf, germany tel: 0211-65 03 01 fax: 0211-65 03 327 sucursal en espa ? a madrid, spain tel: 091-504 27 87 fax: 091-504 28 60 v lizy-villacoublay, france tel: 01-30-67 58 00 fax: 01-30-67 58 99 succursale fran ? aise filiale italiana milano, italy tel: 02-66 75 41 fax: 02-66 75 42 99 branch the netherlands eindhoven, the netherlands tel: 040-244 58 45 fax: 040-244 45 80 branch sweden taeby, sweden tel: 08-63 80 820 fax: 08-63 80 388 united kingdom branch milton keynes, uk tel: 01908-691-133 fax: 01908-670-290 user ? s manual u14364ej3v0um 5 major revisions in this edition pages description pp.44, 46 modification of the size on the adapter block in figures b-2 connection conditions of target system (when np-80gc-tq is used), b-5 connection conditions of target system (when np-80gk is used) addition of b-3 connection conditions of target system (when np-h80gc-tq is used), b-6 connection conditions of target system (when np-h80gk-tq is used) the mark shows major revised points. user?s manual u14364ej3v0um 6 introduction product overview the IE-789418-NS-EM1 is designed to be used with the ie-78k0s-ns or ie-78k0s-ns-a to debug the following target devices that belong to the 78k/0s series of 8-bit single-chip microcontrollers. ? pd789407a subseries: pd789405a, 789406a, 789407a ? pd789417a subseries: pd789415a, 789416a, 789417a target readers this manual is intended for engineers who will use the IE-789418-NS-EM1 with the ie- 78k0s-ns or ie-78k0s-ns-a to perform system debugging. engineers who use this manual are expected to be thoroughly familiar with the target device?s functions and usage methods and to be knowledgeable about debugging. organization when using the IE-789418-NS-EM1, refer to not only this manual (supplied with the ie- 789418-ns-em1) but also the manual that is supplied with the ie-78k0s-ns or ie- 78k0s-ns-a. ie-78k0s-ns IE-789418-NS-EM1 user?s manual user?s manual ? basic specifications ? general ? system configuration ? part names ? external interface functions ? installation ? differences between target devices and target interface circuits ie-78k0s-ns-a user?s manual ? basic specifications ? system configuration ? external interface functions purpose this manual is intended to give users an understanding of the various debugging functions that can be performed when using the IE-789418-NS-EM1. user?s manual u14364ej3v0um 7 terminology the meanings of certain terms used in this manual are listed below. term meaning emulation device this is a general term that refers to the device in the emulator that is used to emulate the target device. it includes the emulation cpu. emulation cpu this is the cpu block in the emulator that is used to execute user-generated programs. target device this is the device (real chip) that is the target for emulation. target system this incl udes the target program and the hardware provided by the user. when defined narrowly, it includes only the hardware. ie system this refers to the combination of the ie-78k0s-ns or ie-78k0s-ns-a and the IE-789418-NS-EM1. conventions data significance: higher digits on the left and lower digits on the right note : footnote for item marked with note in the text caution : information requiring particular attention remark : supplementary information related documents the related documents (user?s manuals) indicated in this publication may include preliminary versions. however, preliminary versions are not marked as such. document name document number ie-78k0s-ns u13549e ie-78k0s-ns-a u15207e IE-789418-NS-EM1 this manual id78k series integrated debugger ver. 2.30 or later operation (windows? based) u15185e pd789407a, 789417a subseries u13952e caution the documents listed above are subject to change without notice. be sure to use the latest documents when designing. user?s manual u14364ej3v0um 8 contents chapter 1 general ........................................................................................................... .................11 1.1 system configuration........................................................................................................ ........................12 1.2 hardware configuration ...................................................................................................... ......................14 1.3 basic specifications ........................................................................................................ ..........................15 chapter 2 part names....................................................................................................... ..............16 2.1 parts of main unit.......................................................................................................... .............................17 chapter 3 installation ...................................................................................................... .............18 3.1 connection .................................................................................................................. ...............................19 3.2 clock settings .............................................................................................................. ..............................20 3.2.1 overview of clock settings ................................................................................................ .............20 3.2.2 main system clock settings ................................................................................................ ............23 3.2.3 subsystem clock settings.................................................................................................. .............28 3.3 mask option setting ......................................................................................................... .........................33 3.3.1 pull-up resistor .......................................................................................................... .....................33 3.3.2 lcd ....................................................................................................................... .........................33 3.4 setting power supply voltage of target interface ............................................................................ ......34 3.5 external trigger............................................................................................................ ..............................35 3.6 switch and jumper settings .................................................................................................. ...................36 chapter 4 differences between target devices and target interface circuits .............................................................................37 appendix a emulation probe pin assignment table........................................................41 appendix b cautions on designing target system..........................................................43 user?s manual u14364ej3v0um 9 list of figures figure no. title page 1-1 system configuration ........................................................................................................ ................................12 1-2 basic hardware configuration................................................................................................ ...........................14 2-1 IE-789418-NS-EM1 part names ................................................................................................. ......................17 3-1 connection of emulation probe............................................................................................... ..........................19 3-2 external circuits used as system clock oscillator ........................................................................... ................20 3-3 when using clock that is already mounted on emulation board (main system clock) ..................................21 3-4 when using clock that is already mounted on emulation board (subsystem clock) .....................................21 3-5 when using user-mounted clock (main system clock) ........................................................................... ........22 3-6 when using user-mounted clock (subsystem clock) ............................................................................. .........22 3-7 when using external clock................................................................................................... ............................23 3-8 connections on parts board (when using user-mounted clock (main system clock))...................................24 3-9 crystal oscillator (when using user-mounted clock (main system clock)).....................................................2 6 3-10 pin alignment of crystal oscillator and socket ............................................................................. ....................26 3-11 connections on parts board (when using user-mounted clock (subsystem clock))......................................29 3-12 crystal oscillator (when using user-mounted clock (subsystem clock))....................................................... .31 3-13 pin alignment of crystal oscillator and socket ............................................................................. ....................31 3-14 pull-up resistor........................................................................................................... ......................................33 3-15 ic7 pin configuration ...................................................................................................... ..................................33 3-16 connection of tp1 and power supply voltage of target system ................................................................ .....34 3-17 external trigger input position ............................................................................................ ..............................35 4-1 equivalent circuit of emulation circuit 1 ................................................................................... ........................39 4-2 equivalent circuit of emulation circuit 2 ................................................................................... ........................39 4-3 equivalent circuit of emulation circuit 3 ................................................................................... ........................40 4-4 equivalent circuit of emulation circuit 4 ................................................................................... ........................40 b-1 distance between in-circuit emulator and conversion socket (80gc) ........................................................... .43 b-2 connection conditions of target system (when np-80gc-tq is used) .........................................................44 b-3 connection conditions of target system (when np-h80gc-tq is used).......................................................44 b-4 distance between in-circuit emulator and conversion adapter (80gk).......................................................... .45 b-5 connection conditions of target system (when np-80gk is used)............................................................... .46 b-6 connection conditions of target system (when np-h80gk-tq is used) .......................................................46 user?s manual u14364ej3v0um 10 list of tables table no. title page 1-1 basic specifications........................................................................................................ .................................. 15 3-1 main system clock settings .................................................................................................. ........................... 23 3-2 subsystem clock settings .................................................................................................... ............................ 28 3-3 switch and jumper settings on ie-78k0s-ns................................................................................... ............... 36 3-4 switch and jumper settings on ie-78k0s-ns-a ................................................................................. ............. 36 3-5 initial setting of jumper on IE-789418-NS-EM1 ............................................................................... ................ 36 a-1 np-80gc, np-80gc-tq, np-h80gc-tq, np-80gk, and np-h80gk-tq pin assignments .......................... 41 user?s manual u14364ej3v0um 11 chapter 1 general the IE-789418-NS-EM1 is a development tool for efficient debugging of hardware or software when using one of the following target devices that belong to the 78k/0s series of 8-bit single-chip microcontrollers. this chapter describes the IE-789418-NS-EM1?s system configuration and basic specifications. ? target device ? pd789407a subseries ? pd789417a subseries chapter 1 general user?s manual u14364ej3v0um 12 1.1 system configuration figure 1-1 illustrates the IE-789418-NS-EM1?s system configuration. figure 1-1. system configuration interface cable (ns if cable) in-circuit emulator ie-78k0s-ns or ie-78k0s-ns-a (sold separately) ac adapter ie-70000-mc-ps-b (sold separately) emulation probe (sold separately) conversion socket/conversion adapter note 3 (sold separately) IE-789418-NS-EM1 (this product) ie-70000-cd-if-a (sold separately) interface card ns card cable control software host machine pc-9800 series or ibm pc/at or compatibles debugger id78k0s-ns (sold separately) device file (available separately) note 1 tm interface cable note 2 interface board ie-70000-98-if-c (sold separately) interface board ie-70000-pc-if-c (sold separately) interface board ie-70000-pci-if-a (sold separately) or mc card cable fg cable chapter 1 general user ? s manual u14364ej3v0um 13 notes 1. the device file is as follows, in accordance with the subseries. s df789418: pd789407a, 789417a subseries the device file can be downloaded from the nec electron devices web site (url:http://www.ic.nec.co.jp/micro). 2. the emulation probes are as follows, in accordance with the package. np-80gc, np-80gc-tq, np-h80gc-tq: for 80-pin plastic qfp (gc type) np-80gk, np-h80gk-tq: for 80-pin plastic tqfp (gk type) the np-80gc, np-80gc-tq, np-h80gc-tq, np-80gk, and np-h80gk-tq are products of naito densei machida mfg. co., ltd. for further information, contact naito densei machida mfg. co., ltd. (tel: +81-45-475-4191) 3. the conversion sockets/conversion adapters are as follows, in accordance with the package. ev-9200gc-80: for 80-pin plastic qfp (gc type: np-80gc) tgc-080sbp: for 80-pin plastic qfp (gc type: np-80gc-tq, np-h80gc-tq) tgk-080sdw: for 80-pin plastic tqfp (gk type) the tgc-080sbp and tgk-080sdw are products of tokyo eletech corporation. for further information, contact daimaru kogyo co., ltd. tokyo electronics department (tel: +81-3-3820-7112) osaka electronics department (tel: +81-6-6244-6672) chapter 1 general user ? s manual u14364ej3v0um 14 1.2 hardware configuration figure 1-2 shows the IE-789418-NS-EM1 ? s position in the basic hardware configuration. figure 1-2. basic hardware configuration ie-78k0s-ns (sold separately)/ ie-78k0s-ns-a (sold separately) IE-789418-NS-EM1 emulation probe (sold separately) dedicated bus interface ie system host machine interface board (sold separately) 78k0s main board emulation board (this product) interface card (sold separately) chapter 1 general user ? s manual u14364ej3v0um 15 1.3 basic specifications the IE-789418-NS-EM1 ? s basic specifications are listed in table 1-1. table 1-1. basic specifications parameter description target device pd789407a, 789417a subseries system clock 1.0 to 5.0 mhz main system clock supply external: clock input from the target system via an emulation probe internal: clock mounted on the emulation board (5.0 mhz) or clock mounted on the parts board by the user subsystem clock supply external: clock input from the target system via an emulation probe internal: clock mounted on the emulation board (32.768 khz) or clock mounted on the parts board by the user target interface voltage v dd = 1.8 to 5.5 v (same as the target device) the IE-789418-NS-EM1 operates on the internal power supply (5 v) when not connected to the target system. user?s manual u14364ej3v0um 16 chapter 2 part names this chapter introduces the parts of the IE-789418-NS-EM1 main unit. the packing box contains the emulation board (IE-789418-NS-EM1), packing list, user?s manual, and guarantee card. if there are any missing or damaged items, please contact an nec sales representative. fill out and return the guarantee card that comes with the main unit. chapter 2 part names user?s manual u14364ej3v0um 17 2.1 parts of main unit figure 2-1. IE-789418-NS-EM1 part names jp1 gnd tp1 lowvolt extout extin probe connector cn1 80gc/80gk led1 sw1 ic7 subsystem clock x3 subsystem clock x1 main system clock x2 jp1 x3 x1 IE-789418-NS-EM1 x2 sw1 led1 cn1 tp1 ic7 user?s manual u14364ej3v0um 18 chapter 3 installation this chapter describes methods for connecting the IE-789418-NS-EM1 to the ie-78k0s-ns or ie-78k0s-ns-a, emulation probe, etc. mode setting methods are also described. caution connecting or removing components to or from the target system, or making switch or other setting changes must be carried out after the power supply to both the ie system and the target system has been switched off. chapter 3 installation user?s manual u14364ej3v0um 19 3.1 connection (1) connection with ie-78k0s-ns or ie-78k0s-ns-a main unit see the ie-78k0s-ns user?s manual (u13549e) note for a description of how to connect the IE-789418-NS-EM1 to the ie-78k0s-ns. note when using the ie-78k0s-ns-a, refer to the ie-78k0s-ns-a user?s manual (u15207e) . (2) connection with emulation probe see the ie-78k0s-ns user?s manual (u13549e) note for a description of how to connect an emulation probe to the IE-789418-NS-EM1. on this board, connect the emulation probe to cn1. note when using the ie-78k0s-ns-a, refer to the ie-78k0s-ns-a user?s manual (u15207e) . caution incorrect connection may damage the ie system. be sure to read the emulation probe?s user?s manual for a detailed description of the connection method. figure 3-1. connection of emulation probe main board (sold separately) (ie-78k0s-ns or ie-78k0s-ns-a) IE-789418-NS-EM1 cn1 80gc, 80gk emulation probe (sold separately) chapter 3 installation user ? s manual u14364ej3v0um 20 3.2 clock settings 3.2.1 overview of clock settings the main system and subsystem clocks to be used during debugging can be selected from (1) to (3) below. (1) clock that is already mounted on emulation board (2) clock that is mounted by user (3) pulse input from target system if the target system includes a clock oscillator, select either (1) clock that is already mounted on emulation board or (2) clock that is mounted by user . for a clock oscillator, a resonator is connected to the target device and the target device ? s internal oscillator is used. an example of the external circuit is shown in part (a) of figure 3-2. during emulation, the oscillator that is mounted on the target system is not used. instead, the clock that is mounted on the emulation board installed for the ie-78k0s-ns or ie-78k0s-ns-a is used. if the target system includes an external clock, select (3) pulse input from target system . for an external clock, a clock signal is supplied from outside the target device and the target device ? s internal oscillator is not used. an example of the external circuit is shown in part (b) of figure 3-2. caution the ie system will be hung-up if the main system clock is not supplied normally. moreover, be sure to input a rectangular wave as the clock from the target. the ie system does not operate if the crystal resonator is connected to x1 (main system clock) and xt1 (subsystem clock). figure 3-2. external circuits used as system clock oscillator (a) clock oscillator (b) external clock x2 or xt2 x2 or xt2 target device target device external clock x1 x1 or xt1 v ss chapter 3 installation user ? s manual u14364ej3v0um 21 (1) clock that is already mounted on emulation board (a) for main system clock a crystal oscillator (x2) is already mounted on the emulation board. its frequency is 5.0 mhz. figure 3-3. when using clock that is already mounted on emulation board (main system clock) ie-78k0s-ns or ie-78k0s-ns-a IE-789418-NS-EM1 clock oscillator or external clock (not used) mounted oscillator (to be used) emulation probe target system remark the clock that is supplied by the IE-789418-NS-EM1 ? s oscillator (encircled in the figure) is used. (b) for subsystem clock a crystal resonator (x3) is already mounted on the emulation board. its frequency is 32.768 khz. figure 3-4. when using clock that is already mounted on emulation board (subsystem clock) ie-78k0s-ns or ie-78k0s-ns-a IE-789418-NS-EM1 mounted resonator (to be used) emulation probe target system clock oscillator or external clock (not used) remark the clock that is supplied by the IE-789418-NS-EM1 ? s resonator (encircled in the figure) is used. chapter 3 installation user ? s manual u14364ej3v0um 22 (2) clock that is mounted by user the user is able to mount any clock supported by the set specifications on the IE-789418-NS-EM1. (a) for main system clock remove the crystal oscillator (x2) that is already mounted on the emulation board, and mount either the parts board on which the resonator to be used is mounted or an oscillator. this method is useful when using a different frequency from that of the pre-mounted clock. figure 3-5. when using user-mounted clock (main system clock) ie-78k0s-ns or ie-78k0s-ns-a IE-789418-NS-EM1 clock oscillator or external clock (not used) target system emulation probe parts board + resonator or oscillator remark the clock that is supplied by the parts board with a resonator or the oscillator on the ie- 789418-ns-em1 (encircled in the figure) is used. (b) for subsystem clock mount the resonator to be used on the parts board (x1) that is already mounted on the emulation board. alternatively, remove the parts board and mount an oscillator. figure 3-6. when using user-mounted clock (subsystem clock) ie-78k0s-ns or ie-78k0s-ns-a target system emulation probe IE-789418-NS-EM1 parts board + resonator or oscillator clock oscillator or external clock (not used) remark the clock that is supplied by the parts board with a resonator or the oscillator on the ie- 789418-ns-em1 (encircled in the figure) is used. chapter 3 installation user ? s manual u14364ej3v0um 23 (3) pulse input from target system an external clock connected to the target system can be used via an emulation probe. figure 3-7. when using external clock ie-78k0s-ns or ie-78k0s-ns-a external clock (to be used) emulation probe target system IE-789418-NS-EM1 remark the clock supplied by the target system ? s external clock (encircled in the figure) is used. 3.2.2 main system clock settings table 3-1. main system clock settings IE-789418-NS-EM1 frequency of main system clock x2 socket cpu clock source selection (id) when using clock that is already mounted on emulation board 5.0 mhz oscillator used when using clock mounted by user oscillator assembled by user internal when pulse is input from target system other than 5.0 mhz oscillator (not used) external caution when a pulse is input from the target system, open the configuration dialog box when starting the integrated debugger (id78k0s-ns) and select ?external? in the area (clock) for selecting the cpu?s clock source (this selects the user clock). remark when the IE-789418-NS-EM1 is shipped, the settings for ? when using clock that is already mounted on emulation board ? are preset. (1) when using clock that is already mounted on emulation board when the IE-789418-NS-EM1 is shipped, a 5.0 mhz crystal oscillator is already mounted in the ie-789418-ns- em1 ? s x2 socket. when using the factory-set mode settings, there is no need to make any other hardware settings. when starting the integrated debugger (id78k0s-ns), open the configuration dialog box and select ? internal ? in the area (clock) for selecting the cpu ? s clock source (this selects the emulator ? s internal clock). chapter 3 installation user ? s manual u14364ej3v0um 24 (2) when using clock mounted by user the settings described under either (a) or (b) are required, depending on the type of clock to be used. when starting the integrated debugger (id78k0s-ns), open the configuration dialog box and select ? internal ? in the area (clock) for selecting the cpu ? s clock source (this selects the emulator ? s internal clock). (a) when using a ceramic resonator or crystal resonator ? items to be prepared ? parts board ? capacitor ca ? ceramic resonator or crystal resonator ? capacitor cb ? resistor rx ? solder kit chapter 3 installation user ? s manual u14364ej3v0um 25 <2> prepare the IE-789418-NS-EM1. <3> remove the crystal oscillator that is mounted in the IE-789418-NS-EM1 ? s socket (the socket marked as x2). <4> connect the parts board (from <1> above) to the socket (x2) from which the crystal oscillator was removed. check the pin 1 mark to make sure the board is mounted in the correct direction. <5> make sure that the parts board is wired as shown in figure 3-8 above. <6> install the IE-789418-NS-EM1 in the ie-78k0s-ns or ie-78k0s-ns-a. the above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. 1 m ? 11 4 3 12 ca cb 13 2 5 10 rx 98 6 hcu04 hcu04 x hc157 pd789009 hsk120 1 m ? 100 ? lv cc x1 x1 pd789009 ie-78k0s-ns or ie-78k0s-ns-a side (emulation device) remark the sections enclosed in broken lines indicate parts that are attached to the parts board. chapter 3 installation user ? s manual u14364ej3v0um 26 (b) when using a crystal oscillator ? items to be prepared ? crystal oscillator (see pinouts shown in figure 3-9) figure 3-9. crystal oscillator (when using user-mounted clock (main system clock)) chapter 3 installation user ? s manual u14364ej3v0um 27 the above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. v cc crystal oscillator hc157 pd789009 hsk120 1 m ? 100 ? lv cc x1 x1 pd789009 ie-78k0s-ns or ie-78k0s-ns-a side (emulation device) (3) when pulse is input from target system no hardware settings are required for this situation. when starting the integrated debugger (id78k0s-ns), open the configuration dialog box and select ? external ? in the area (clock) for selecting the cpu ? s clock source (this selects the user ? s clock). chapter 3 installation user ? s manual u14364ej3v0um 28 3.2.3 subsystem clock settings table 3-2. subsystem clock settings IE-789418-NS-EM1 frequency of sub system clock to be used x1 socket jp1 when using clock (x3) that is already mounted on emulation board 32.768 khz 6 and 8 shorted when using clock mounted by user oscillator assembled by user short 2 to 3 side when pulse is input from target system other than 32.768 khz not used short 1 to 2 side caution jumper jp1, which is used to select the board ? s clock or an external clock, should be set only after turning off the power of the ie-78k0s-ns or ie-78k0s-ns-a. remark when the IE-789418-NS-EM1 is shipped, the settings for ? when using clock that is already mounted on emulation board ? are preset. (1) when using clock that is already mounted on emulation board when the IE-789418-NS-EM1 is shipped, a 32.768 khz crystal resonator (x3) and the parts board (x1) on which pins 6 and 8 are shorted are already mounted on the IE-789418-NS-EM1. short the 2 to 3 side on the ie- 789418-ns-em1 ? s jumper (jp1). there is no need to make any other settings via the integrated debugger (id78k0s-ns). (2) when using the clock mounted by user the settings described under either (a) or (b) are required, depending on the type of clock to be used. short the 2 to 3 side on the IE-789418-NS-EM1 ? s jumper (jp1). there is no need to make any other settings via the integrated debugger (id78k0s-ns). (a) when using a ceramic resonator or crystal resonator ? items to be prepared ? parts board ? capacitor ca ? ceramic resonator or crystal resonator ? capacitor cb ? resistor rx ? solder kit chapter 3 installation user ? s manual u14364ej3v0um 29 figure 3-11. connections on parts board (when using user-mounted clock (subsystem clock)) parts board (x1) pin no. connection 2-13 capacitor ca 3-12 capacitor cb 4-11 ceramic resonator or crystal resonator 5-10 resistor rx 8-9 short circuit diagram remark the sections enclosed in broken lines indicate parts that are attached to the parts board. 1 2 3 4 5 6 7 14 13 12 11 10 9 8 10 m ? 11 4 3 12 cb ca 13 2 5 10 rx 9 8 clock out hcu04 hcu04 chapter 3 installation user ? s manual u14364ej3v0um 30 <3> make sure that the parts board (x1) is wired as shown in figure 3-11. <4> install the IE-789418-NS-EM1 in the ie-78k0s-ns or ie-78k0s-ns-a. the above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. 10 m ? hcu04 hcu04 9 8 5 rx 10 11 4 13 ca 2 3 cb 12 ie-78k0s-ns or ie-78k0s-ns-a side (emulation device) target system 3 1 jp1 clk in 2 remark the section enclosed in broken lines indicates parts that are attached to the parts board. chapter 3 installation user ? s manual u14364ej3v0um 31 (b) when using a crystal oscillator ? items to be prepared ? crystal oscillator (see pinouts shown in figure 3-12) figure 3-12. crystal oscillator (when using user-mounted clock (subsystem clock)) chapter 3 installation user ? s manual u14364ej3v0um 32 the above steps configure the following circuit and enable supply of the clock from the mounted oscillator to the emulation device. +5v 8 7 14 target system ie-78k0s-ns or ie-78k0s-ns-a side (emulation device) parts board crystal oscillator jp1 clk in 1 3 2 (3) when inputting pulse from target system short the 1 to 2 side on the IE-789418-NS-EM1 ? s jumper (jp1). there is no need to make any settings via the integrated debugger (id78k0s-ns). chapter 3 installation user ? s manual u14364ej3v0um 33 3.3 mask option setting 3.3.1 pull-up resistor by setting the dip switch (sw1) in the IE-789418-NS-EM1, a 33 k ? pull-up resistor can be connected to p50 to p53 as specified by the mask option. for ports that do not exist in the IE-789418-NS-EM1, set to the dip switch off. the pull-up resistor is pulled up by the v dd pin of the target socket. figure 3-14. pull-up resistor target v dd emulation cpu 33 k ? 100 k ? p50 p51 p52 off p53 sw1 initial setting is off probe p50 p51 p52 p53 p50 p51 p52 p53 3.3.2 lcd in the IE-789418-NS-EM1, a dividing resistor for lcd drive set by a mask option can be mounted on the ic7 parts board. figure 3-15. ic7 pin configuration v ss v lc2 v lc1 v lc0 bias ic7 16 15 14 13 12 11 10 9 12345678 chapter 3 installation user ? s manual u14364ej3v0um 34 3.4 setting power supply voltage of target interface in the ie system, emulation is possible with a voltage of the same level as the power supply voltage of the target system. when the target system is not connected, the ie system automatically operates with the emulator ? s internal power supply (5 v). when debugging with a voltage that is the same level as that of the target system, supply the same voltage as that of the target system to the tp1 terminal pin of the IE-789418-NS-EM1 (the same applies when the voltage is 5 v). set the target voltage to between 1.8 and 5.0 v. ? maximum current consumption of tp1 1.8 to 5.0 v: approximately 100 ma figure 3-16. connection of tp1 and power supply voltage of target system gnd v dd emulation probe target system power supply voltage of target system tp1 gnd lowvolt jp1 x3 x1 IE-789418-NS-EM1 x2 sw1 led1 ic7 cn1 caution connect tp1 on the board and the power supply voltage of the target system after turning off the power of the ie-78k0s-ns or ie-78k0s-ns-a. remark the v dd pin of the target system is only used for controlling led1 (tv cc ), which monitors whether the power supply of the target system is connected in the IE-789418-NS-EM1. chapter 3 installation user ? s manual u14364ej3v0um 35 3.5 external trigger to set up an external trigger, connect it to the IE-789418-NS-EM1 ? s check pins extout and extin as shown below. see the ie-78k0s-ns user ? s manual (u13549e) or ie-78k0s-ns-a user ? s manual (u15207e) for pin characteristics, and the id78k series integrated debugger ver. 2.30 or later operation (windows based) (u15185e) for the usage methods. (1) extout outputs a low level from the extout pin on the IE-789418-NS-EM1 for 1.3 s upon the occurrence of a break event. caution connect a pull-up resistor on the target system since this is an open-drain output. (2) extin an event signal can be input from the extin pin on the IE-789418-NS-EM1. input a high-level pulse signal for 2 cpu operation clocks or more. figure 3-17. external trigger input position external trigger extout extin jp1 x3 IE-789418-NS-EM1 led1 cn1 tp1 chapter 3 installation user ? s manual u14364ej3v0um 36 3.6 switch and jumper settings (1) switch and jumper settings on the ie-78k0s-ns when using the IE-789418-NS-EM1, set the switches and jumpers on the ie-78k0s-ns as shown in table 3-3. for details of these switch and jumper settings, refer to the ie-78k0s-ns user ? s manual (u13549e) . table 3-3. switch and jumper settings on ie-78k0s-ns sw1 sw3 sw4 jp1 jp4 setting off all switches on all switches on 2 to 3 shorted 1 to 2 shorted caution if the jumpers and switches are set incorrectly, the board may be damaged. (2) switch and jumper setting on ie-78k0s-ns-a when using the IE-789418-NS-EM1, set the switches and jumpers on the ie-78k0s-ns-a as shown in table 3-4. for the position of the switches and jumpers, refer to the ie-78k0s-ns-a user ? s manual (u15207e) . table 3-4. switch and jumper settings on ie-78k0s-ns-a sw1 jp1 jp3 setting off 1-2 shorted (fixed) caution if the jumpers and switches are set incorrectly, the board may be damaged. (3) jumper setting on the IE-789418-NS-EM1 the initial setting of jumper on the IE-789418-NS-EM1 is as shown in table 3-5. for details, refer to 3.2 clock settings . table 3-5. initial setting of jumper on IE-789418-NS-EM1 jp1 setting 2 to 3 shorted user?s manual u14364ej3v0um 37 chapter 4 differences between target devices and target interface circuits this chapter describes differences between the target device?s signal lines and the signal lines of the ie-789418- ns-em1?s target interface circuit. although the target device is a cmos circuit, the IE-789418-NS-EM1?s target interface circuit consists of emulation circuits such as an emulation cpu, ttl, and cmos-ic. when the ie system is connected with the target system for debugging, the ie system performs emulation so as to operate as the actual target device would operate in the target system. however, some minor differences exist since the operations are performed via the ie system?s emulation. (1) signals input to or output from the eva chip and the peripheral eva chip (2) signals input from the target system via a gate (3) analog signals (4) other signals the IE-789418-NS-EM1?s circuit is used as follows for signals listed in (1) to (4) above. (1) signals input to or output from the eva chip and peripheral eva chip the following signals perform the same operations as in the pd789407a, 789417a subseries. however, a 1 m ? pull-down resistor and 100 ? resistor are inserted in series. refer to figure 4-1 equivalent circuit of emulation circuit 1 . ? signals related to port 0 ? signals related to port 2 ? signals related to port 4 ? signals related to port 5 (2) signals input from the target system via a gate since the following signals are input via a gate, their signals show a delay compared to the pd789407a, 789417a subseries. refer to figure 4-2 equivalent circuit of emulation circuit 2 . ? reset signal ? signals related to x1, xt1 chapter 4 differences between target devices and target interface circuits user?s manual u14364ej3v0um 38 (3) analog signals because the following signals input/output analog signals, special processing is not performed in the ie-789418- ns-em1. refer to figure 4-3 equivalent circuit of emulation circuit 3 . ? av dd ? av ref ? s0 to s15 ? com0 to com3 ? port 6 ? port 8 ? port 9 ? v lc0 to v lc2 ? bias (4) other signals refer to figure 4-4 equivalent circuit of emulation circuit 4 . ? v dd0 and v dd1 pins the emulation cpu operates on the internal power supply (5 v) of the IE-789418-NS-EM1 when not connected to the target system, and operates on the voltage supplied from the voltage supply pin (tp1) when connected to the target system. the v dd0 and v dd1 pins of the target system are used only to control the led (tv cc ) that indicates whether the target system?s power is on or off. ? v ss0 , v ss1 , and av ss pins the v ss0 , v ss1 , and av ss pins are connected to gnd in the IE-789418-NS-EM1. ? test/v pp pin the test/v pp pin is not used in the IE-789418-NS-EM1. ? x2 and xt2 pins the x2 and xt2 pins are not used in the IE-789418-NS-EM1. chapter 4 differences between target devices and target interface circuits user?s manual u14364ej3v0um 39 figure 4-1. equivalent circuit of emulation circuit 1 probe side IE-789418-NS-EM1 side 100 ? 100 ? 1 m ? 33 k ? 1 m ? lv cc sw1 1 m ? 100 ? port 0 port 2 port 4 port 5 port 0 port 2 port 4 port 5 figure 4-2. equivalent circuit of emulation circuit 2 reset x1 xt1 xt1 x1 reset 1 m ? 100 ? 100 ? 100 ? 4.7 k ? lv cc lv cc lv cc hc4066 hc157 pd789009 pd789009 x2 x1 hsk120 1 m ? pd789009 hsk120 hc04 pd789009 chapter 4 differences between target devices and target interface circuits user ? s manual u14364ej3v0um 40 figure 4-3. equivalent circuit of emulation circuit 3 mask option av dd av ref s0 to s15 com0 to com3 port 6 port 8 port 9 v lc0 to v lc2 bias av dd av ref s0 to s15 com0 to com3 port 6 port 8 port 9 v lc0 to v lc2 bias probe side IE-789418-NS-EM1 side figure 4-4. equivalent circuit of emulation circuit 4 ie-789831-ns-em1 side g6h-2f (relay) filter 100 ? 1 m ? pc393 test/v pp test/v pp x2 xt2 v ss0 v ss1 av ss v dd1 v dd0 n. c. n. c. lv cc probe side 22 f user?s manual u14364ej3v0um 41 appendix a emulation probe pin assignment table table a-1. np-80gc, np-80gc-tq, np-h80gc-tq, np-80gk, and np-h80gk-tq pin assignments (1/2) emulation probe cn1 pin no. emulation probe cn1 pin no. 1 114 33 56 2 113 34 49 3 108 35 50 4 107 36 45 5 104 37 46 6 103 38 41 7 100 39 42 8994035 994418 10 93 42 7 11 30 43 14 12 29 44 13 13 24 45 18 14 23 46 17 15 20 47 22 16 19 48 21 17 16 49 28 18 15 50 27 19 10 51 92 20 9 52 91 21 37 53 98 22 43 54 97 23 44 55 102 24 47 56 101 25 48 57 106 26 51 58 105 27 52 59 112 28 57 60 111 29 58 61 83 30 59 62 77 31 60 63 78 32 55 64 73 remarks 1. the np-80gc, np-80gc-tq, np-h80gc-tq, np-80gk, and np-h80gk-tq are products of naito densei machida mfg. co., ltd. 2. the numbers in the ?emulation probe? column indicate the corresponding pin number on the emulation probe tip. appendix a emulation probe pin assignment table user?s manual u14364ej3v0um 42 table a-1. np-80gc, np-80gc-tq, np-h80gc-tq, np-80gk, and np-h80gk-tq pin assignments (2/2) emulation probe cn1 pin no. emulation probe cn1 pin no. 65 74 73 66 66 69 74 71 67 70 75 72 68 63 76 75 69 64 77 76 70 61 78 79 71 62 79 80 72 65 80 85 remarks 1. the np-80gc, np-80gc-tq, np-h80gc-tq, np-80gk, and np-h80gk-tq are products of naito densei machida mfg. co., ltd. 2. the numbers in the ?emulation probe? column indicate the corresponding pin number on the emulation probe tip. user?s manual u14364ej3v0um 43 appendix b cautions on designing target system figures b-1 to b-6 show the conditions when connecting the emulation probe to the conversion adapter or conversion socket. follow the configuration below and consider the shape of parts to be mounted on the target system when designing a system. of the products described in this chapter, the np-80gc, np-80gc-tq, np-h80gc-tq, np-80gk and np- h80gk-tq are products of naito densei machida mfg. co., ltd, and the tgc-080sbp and tgk-080sdw are products of tokyo eletech corporation. (1) np-80gc, np-80gc-tq, np-h80gc-tq figure b-1. distance between in-circuit emulator and conversion socket (80gc) 170 mm note in-circuit emulator ie-78k0s-ns or ie-78k0s-ns-a emulation board IE-789418-NS-EM1 conversion socket: ev-9200gc-80 or conversion adapter: tgc-080sbp target system cn1 emulation probe np-80gc, np-80gc-tq np-h80gc-tq note when np-h80gb-tq is used, the distance is 370 mm. appendix b cautions on designing target system user ? s manual u14364ej3v0um 44 figure b-2. connection conditions of target system (when np-80gc-tq is used) emulation probe np-80gc-tq emulation board IE-789418-NS-EM1 24.8 mm 25 mm 40 mm 34 mm target system conversion adapter tgc-080sbp 21 mm 21 mm 11 mm figure b-3. connection conditions of target system (when np-h80gc-tq is used) emulation probe np-h80gc-tq emulation board IE-789418-NS-EM1 25.3 mm 25 mm 42 mm 45 mm target system conversion adapter tgc-080sbp 21 mm 21 mm 11 mm appendix b cautions on designing target system user ? s manual u14364ej3v0um 45 (2) np-80gk, np-h80gk-tq figure b-4. distance between in-circuit emulator and conversion adapter (80gk) 170 mm note in-circuit emulator ie-78k0s-ns or ie-78k0s-ns-a emulation board IE-789418-NS-EM1 conversion adapter tgk-080sdw target system cn1 emulation probe np-80gk, np-h80gk-tq note when np-h80gk is used, the distance is 370 mm. appendix b cautions on designing target system user ? s manual u14364ej3v0um 46 figure b-5. connection conditions of target system (when np-80gk is used) emulation probe np-80gk emulation board IE-789418-NS-EM1 24.8 mm 25 mm 40 mm 34 mm target system conversion adapter tgk-080sdw 18 mm 18 mm 11 mm figure b-6. connection conditions of target system (when np-h80gk-tq is used) emulation probe np-h80gk-tq emulation board IE-789418-NS-EM1 25.3 mm 25 mm 42 mm 45 mm target system conversion adapter tgk-080sdw 18 mm 18 mm 11 mm although nec has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. despite all the care and precautions we've taken, you may encounter problems in the documentation. please complete this form whenever you'd like to report errors or suggest improvements to us. hong kong, philippines, oceania nec electronics hong kong ltd. fax: +852-2886-9022/9044 korea nec electronics hong kong ltd. seoul branch fax: +82-2-528-4411 p.r. china nec electronics shanghai, ltd. nec electronics taiwan ltd. fax: +86-21-6841-1137 address north america nec electronics inc. corporate communications dept. fax: +1-800-729-9288 +1-408-588-6130 europe nec electronics (europe) gmbh market communication dept. fax: +49-211-6503-274 south america nec do brasil s.a. fax: +55-11-6462-6829 taiwan asian nations except philippines nec electronics singapore pte. ltd. fax: +886-2-2719-5951 fax: +65-250-3583 japan nec semiconductor technical hotline fax: +81- 44-435-9608 i would like to report the following error/make the following suggestion: document title: document number: page number: thank you for your kind support. if possible, please fax the referenced page or drawing. excellent good acceptable poor document rating clarity technical accuracy organization cs 02.3 name company from: tel. fax facsimile message |
Price & Availability of IE-789418-NS-EM1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |